topbanner.gif
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Shoutbox
You must login to post a message.

snwcmpr
08/18/2019 4:31 AM
Awesome I sent an email to AllenB and JackH The email to JackH failed. I had screenshots of my settings.

allenb
08/18/2019 3:37 AM
Jack and I are enlisting help from our PHP site admin to try and solve as soon as possible. Thanks for letting us know.

snwcmpr
08/18/2019 2:53 AM
I got another PM last night......... No email notice.

snwcmpr
08/17/2019 7:36 AM
Email address correct. I constantly check junk folder. I turned off, then on, the setting to receive notice.

JackH
08/17/2019 7:10 AM
Also check that there are no spam filters set for email.

Users Online
Guests Online: 1

Members Online: 0

Total Members: 6,099
Newest Member: kla65
In Memory Of Ginny
Donations

Latest Donations
allenb - 25.00
snwcmpr - 10.00
Groveland Hill Roas... - 25.00
renatoa - 2.00
JitterzZ - 50.00

View Thread

Who is here? 1 guest(s)
 Print Thread
Transparent Fluid Bed Design
CK
Hey, it looks quite interesting! Looking forward to the video.


The video has been updated. Here's a picture of what internals are inside the body.
CK attached the following image:
roaster_internals.jpg

Edited by CK on 12/20/2018 8:50 AM
 
CK
Here's a view of the air passage holes with duct work removed.
CK attached the following image:
roaster_internals_air_ducting_removed.jpg
 
CK
This is the top side taken apart to insulate the heater. Without ceramic insulation the regular PLA plastic covers melt/deform easily. I did experiment with high temp 3DK TOP PLA filament. It is food grade, and can withstand temps to 230C, however, when annealed, it shrinks about 3-4% which makes it a challenge to design to specification.
CK attached the following image:
roaster_heater_and_blower_internals_r1_1.jpg

Edited by CK on 01/09/2019 8:43 AM
 
CK
Here's a video showing the custom HEPA filter on the intake side.


Edited by CK on 03/17/2019 7:45 AM
 
greencardigan
Great info!

Can you tell us more about the logging setup you are using? It looks like a thermocouple connected to a tablet?

And what are the three displays for?
 
CK
Thanks greencardigan,

There are 2 thermocouples in this machine... 1 in the hot air supply tube below the RC, and 1 in the top of the machine. The top connection is a custom soldered USB male/female connector to the thermocouple wires, allowing the top to detach.

These 2 sensors interface with a Yoctopuce thermocouple module, and Coffee Roaster Pro android software.

The 3 displays are power meters... They allow me to measure power consumption of the machine's 3 separate circuits, and at the same time avoid tripping circuit breakers. They aren't needed, but have helped learn the system.

A few days ago I insulated the heater body. After roasting 4 batches, the power meters showed the power savings when compared to the original roaster without insulation.
Edited by CK on 12/28/2018 7:20 AM
 
CK
Here are some numbers from the last day of roasting with the machine. Roast #1 used the most power because the machine was not preheated before beginning. The following 3 roasts, after machine preheating, all had very similar w/hr usage despite having different bean charges.
CK attached the following image:
power_consumption_for_roasts_dec_2018.png
 
CK
Air flow mapping the insulated transparent roaster.
CK attached the following image:
insulated_transparent_roaster_air_flow_mapping.jpg
 
CK
Here is a view of the heater housing used from a Twobiu hot air popper. Inside is the large coil (heater 1) of the Twobiu popper with the small coil removed. Heater 2 is from a Popflix popper. It is sandwiched on top of heater 1. The Popflix mica plates were trimmed with a dremel to fit this housing. Airflow comes up the center of the bottom heater - flows outwards towards the steel case passing heater coil 1 - then flows upwards along the wall of the case and inwards passing the Popflix heat coil 2 - finally exiting out the top center into the delivery pipe.
CK attached the following image:
custom_heater.jpg
 
CK
A video of how the roast chamber and chaff collection chamber can be washed.

 
renatoa
How often they need washing ?
 
CK
renatoa wrote:

How often they need washing ?


This was after about 6 roasts. Normally after a day of roasting I store the machine in my office for a few weeks. I prefer to clean the containers before storing them, otherwise there can be a smell of residuals from chaff and oils.
 
renatoa
Similar to the glass of the turbo oven lid.
Asked because I didn't seen so far nobody mentioning this detail for their FB or TO glass maintenance. Only the Gene guys sometimes.
Also curious how the drums roasters aren't cleaned for years, and not accumulating tons of residues...
 
CK
In case anyone else is building a roaster that has 3D printed parts on the machine, you may want to install threaded inserts for a stronger connection. This is a simple and effective technique of how to do it.

Before these inserts, I used generic wood screws to hold parts together. That often caused the plastic to split when tightening, and the threads stripped easily. These cheap inserts are much better for making strong connections on your model.

The custom tool I'm using is a 20mm M3 hex screw with the leftover silicone feet from a hot air popper. These insulate my fingers from the hot screw. I put nuts on the screw to space out the silicone feet so they cover nearly the whole 20mm length. Just the tip of the screw is available for putting your threaded insert on as seen in the video. When you set the insert to the plastic, the silicone feet act as a natural level for the install.

 
Brandon
I really like this design and execution. Well done!
 
CK
Thanks Brandon, I'll be posting a parts list soon in case anyone would like to do something similar.
 
eltakeiteasy
This is the coolest roaster I have ever seen! I have been searching to make my own and this is absolutely amazing! Hat off to you sir!
 
jessep
CK wrote:

Thanks Brandon, I'll be posting a parts list soon in case anyone would like to do something similar.



yes please!
 
CK
Here's the completed transparent roaster with insulation and aesthetic covers over the insulated heater. The top in this image is removed for loading/unloading beans or chaff.
CK attached the following image:
transparent_roaster_completed_top_removed.jpg
 
eltakeiteasy
CK wrote:

Here's the completed transparent roaster with insulation and aesthetic covers over the insulated heater. The top in this image is removed for loading/unloading beans or chaff.


Looks great!
 
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
Preferred Control Method Fluid Bed Roaster Fluidbed Roaster 7 07/31/2019 11:06 AM
Preferred Acquisition of a Fluid Bed Roaster Fluidbed Roaster 4 07/01/2019 5:47 AM
Fluid Bed Build Building a Coffee Roaster 15 06/29/2019 6:19 AM
DIY Fluid Bed Roaster (2lb) New Members say hello or you may update your profile. 2 06/26/2019 12:15 PM
3d Printed Fluid Bed Roaster Building a Coffee Roaster 57 06/26/2019 8:57 AM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion Copyright © 2019 PHP-Fusion Inc
Released as free software without warranties under GNU Affero GPL v3
Designed with by NetriX