Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
You must login to post a message.

· 04/02/2020 4:50 AM
Morning Ed, I haven't done any green coffee hoarding yet but am hoping the supplies don't end up like the toilet paper isles!

· 03/31/2020 2:53 PM
Hey Ed. Thanks. roar

· 03/31/2020 11:21 AM
Hey quarantined home roasters! I hope you have great coffee! If they have a run on coffee, I hope you're set with your great home roast! Find me on Facebook! Ed Needham

· 03/25/2020 11:49 AM
New Rochelle in the news. I think of you every time I hear it. ... Please stay safe.

· 03/21/2020 7:36 AM
Good morning homeroasters morning Everyone is hopefully staying healthy through this. Hang in there and stay safe!

Users Online
Guests Online: 4

Members Online: 0

Total Members: 6,467
Newest Member: hehevt
In Memory Of Ginny

Latest Donations
Anonymous - 5.00
Anonymous - 5.00
renatoa - 2.00
JitterzZ - 2.01
renatoa - 2.00

View Thread

Who is here? 1 guest(s)
 Print Thread
Dereks 1-2Kg drum roaster build


Lylabrown wrote:

I recommend swapping out the socket-cap screws that attach the vanes to the drum with button or round headed ones instead. The reason being that the beans have the uncanny ability to wedge themselves in any bean-width gap and stay there!

Good catch!


Lylabrown wrote:
Based on bad experiences I’ve had building various drum/vane configurations I recommend swapping out the socket-cap screws that attach the vanes to the drum with button or round headed ones instead. The reason being that the beans have the uncanny ability to wedge themselves in any bean-width gap and stay there until the next roast, or multiple roasts, before eventually freeing themselves and finding there way into the cup. Resulting in a bitter, nasty cup of joe!

Very good catch. Thx, I'll address that.

I turned my attention to the cabinet frames and how I was going to fix the skin. Came up with some brackets which I've welded up. They have 3mm sections in them so as to provide something to tap a thread. Had to rework the frame ribs to accommodate this.

Was a bit cumbersome but have also put the inner chamber skin together. I might have to revisit this. It's made from 0.9mm stainless which difficult to TIG and I am not sure how it will stand up once running. Stainless warps when subject to heat so we'll see.
I've already adjusted the front and rear supports to 1.5mm and I may consider splitting the main skin into two parts that can be bolted together. The total length of the single piece is awkward to ship from the cutting shop.
Also I don't think the assy needs to be welded together - extra tabs that you can fold over will suffice and make it easier to put together.
Got round to finishing the inner skin and mounted in the frame.

The rear plate hole for the drive shaft doesn't allow too much clearance so I've mounted a length of 5mm threaded rod which extends into a 5mm well I drilled into the rear plate. This should hold the assy in place in the event of any movement due to heat expansion/warping.

The assy fits flush between the end and front plates exactly and clamps it up when they're bolted on.

Managed to form the cabinet skin by hand using just my argon cylinder and a length of wooden round I had which was about the right size.

Starting to look like a roaster..
It is looking great! You have put a lot of work into it over the past few years.

KKTO Roaster.
looking really great!
Now... stand up and walk ! er... roast Grin
Looking good :-)
Inching ever forward.. My draw tube and damper-baffle assy has come together. The handle is a re-purposed Faema e61 grouphead brew lever.
And tigged the cyclone bottom plate in place to support cooling draw tube assy..
Hello dmccallum!
Searching for information to build my own roaster I just found your post here.

Amazing post! Lot, and I meen a LOT of information you have shared here. Construction methods, materials, R&D on the cyclon and more, details pictures, almost everything about it.

I would like to thank you for all you've shared here and congratulations for your work.
Have you finish it? It is working?
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
KKTO Build Turbo Oven Roasters 72 04/02/2020 8:16 AM
Tri-Clamp Roaster Fluidbed Roaster 25 04/02/2020 4:12 AM
Fluidbed Roaster project Fluidbed Roaster 56 03/31/2020 6:25 PM
Bobby M15's drum Drum Roasters 242 03/31/2020 5:52 PM
Fluid Bed Roaster Build - bye bye Heat Gun and Flour Sifter Fluidbed Roaster 127 03/28/2020 6:06 PM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion copyright © 2002 - 2020 by Nick Jones.
Released as free software without warranties under GNU Affero GPL v3.
Designed with by NetriX