topbanner.gif
January 22, 2018 22:50:07
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Navigation
bullet2.gif HOMEROASTERS.ORG
bullet2.gif Active Forums
bullet2.gif FORUM INDEX
bullet2.gif Downloads
bullet2.gif News
bullet2.gif Forum FAQ
bullet2.gif Contact Me
bullet2.gif Photo Gallery
bullet2.gif Search
bullet2.gif User's Voice
bullet2.gif Facebook Connect
bullet2.gif Videos
Forum Threads
Newest Threads
bullet2.gif Poppery 2 and Artisan
bullet2.gif Kaldi Wide with Camp...
bullet2.gif Bobby M15's drum
bullet2.gif Looking for TC4C board
bullet2.gif Auber syl-2381-s and...
Hottest Threads
bullet2.gif TC4 with aArtisan... [275]
bullet2.gif Bobby M15's drum [107]
bullet2.gif Dereks 1-2Kg drum... [89]
bullet2.gif Looking for TC4C ... [61]
bullet2.gif Honey Badger 1k [41]
Users Online
bullet2.gif Guests Online: 5

bullet2.gif Members Online: 0

bullet2.gif Total Members: 5,220
bullet2.gif Newest Member: swanston
BotSlap Panel
bullet2.gif Last check: 01.22.18
bullet2.gif Slap count: 0
bullet2.gif Last checked ID: 6437
View Thread
Homeroasters.org » BUILDING A ROASTER » Drum Roasters
Who is here? 2 guest(s)
 Print Thread
Dereks 1-2Kg drum roaster build
BobbyS
When you open the slide on the hopper, what keeps some of the beans from going out the exhaust on top?
 
dmccallum
The tube the beans drop through is about 15-20mm away from the horizontal draw tube so I'm not anticipating losing any as you'd have the damper closed when dropping.
That's the theory..
 
dmccallum
Have made some progress on the cyclone while I wait for other parts to be machined.
I created some templates for notching the incoming draw pipe and matching hole in the cylinder wall.
dmccallum attached the following images:
20171229_173926.jpg 20171229_172850.jpg 20171229_172759.jpg 20171229_162423.jpg 20180101_151402.jpg
 
dmccallum
I'm a beginner TIG welder and while I've had some one-on-one tuition there's still a fair bit to learn. Stainless steel warps terribly when heated and while I did a weld on the inside to attach the draw pipe and things were ok, I followed it up with a TIG braze on the outside with siliconbronze and applied too much heat. Shouldn't have done that - it was only for cosmetic reasons.
It can be corrected though by fitting the top ring to hold it true and I have had to get this part cut again in 3mm to cope with it. I have added a couple of additional bottom plates to the cutting files for the purpose of holding the cylinder to a true round during the welding process.

The cylinder wasn't entirely a true round when it came from the shop, but a beefed up 3mm top and bottom plate fixes any minor defects. Note to self in future would be to ask your fabricator what their capability is here. I'll be down to whether their slip-roller handles the ends of the material. I can't complain though about what they've produced as it can be handled.
dmccallum attached the following images:
20180104_230709.jpg 20180103_152631.jpg 20180103_152623.jpg 20180103_111040.jpg
 
dmccallum
Machined parts arrived and I've played a bit with fitting up.
dmccallum attached the following images:
20180104_230854.jpg 20180104_231042.jpg 20180104_231028.jpg 20180104_230956.jpg 20180104_230811.jpg 20180104_230655.jpg
 
dmccallum
Machined parts back from my usual bloke. The drive shaft is 15mm in the middle with the ends turned down to 12mm to fit the bearing ends and a keyway milled for the chain-ring.
dmccallum attached the following image:
20180104_120039.jpg
 
allenb
Hey Derek,
After seeing your design and fabrication prowess, I'm ashamed to look at my drum roaster!

Can't wait to see this all come together into a complete roaster!

BTW, whats the procedure for getting the spokes into the holes of the drum? Back out each spoke from the hub once in place and backup nut on the threaded end at the hub? This would make it adjustable for centering the works.

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
dmccallum
allenb wrote:
BTW, whats the procedure for getting the spokes into the holes of the drum? Back out each spoke from the hub once in place and backup nut on the threaded end at the hub? This would make it adjustable for centering the works.


Hi Allen
That's the idea. The rear collar on the shaft will also allow you to fasten the drums perforated back plate once it's running true.

Have to approach getting the vanes mounted inside the drum next which will be fiddly.
dmccallum attached the following image:
20180106_100247.jpg
 
allenb
If welding, be sure to utilize magnets where possible for holding in place.

Be sure to leave an adequate gap between front end of vanes and front plate. I'd go no less than 3/4" and for the size roaster you're building, I'd go for 1".

Are you going to attach the return vanes to the forward vanes or attach to the shaft?

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
dmccallum
allenb wrote:
Be sure to leave an adequate gap between front end of vanes and front plate. I'd go no less than 3/4" and for the size roaster you're building, I'd go for 1".

Are you going to attach the return vanes to the forward vanes or attach to the shaft?


Thx for that. I think i'd gone for about 15mm back from front plate going on previous threads - I'll bump it up to 20mm.

The return vanes will sit on top of the forward vanes. I have some pegs to put in place on the drum which both sets will be welded to.
 
Jump to Forum:
Similar Threads
Thread Forum Replies Last Post
Bobby M15's drum Drum Roasters 108 01-20-2018 19:09
Build a Chaff Collector Cyclone Building a Coffee Roaster 33 01-13-2018 23:22
Brilliant guy from Malaysia's 800 gr. build Drum Roasters 8 12-30-2017 22:52
Ikea inspired DIY home coffee roaster New Members say hello or you may update your profile. 5 12-28-2017 11:56
FZ-94 100g--2.4kg roaster Drum Roaster (Store Bought and Commercial) 5 12-23-2017 04:15