topbanner.gif
May 24 2017 06:29:43
Login
Username

Password



Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Navigation
bullet2.gif HOMEROASTERS.ORG
bullet2.gif Active Forums
bullet2.gif FORUM INDEX
bullet2.gif Downloads
bullet2.gif News
bullet2.gif Forum FAQ
bullet2.gif Contact Me
bullet2.gif Photo Gallery
bullet2.gif Search
bullet2.gif User's Voice
Forum Threads
Newest Threads
bullet2.gif SUCCESS!!! Finally...
bullet2.gif Help needed with TC4...
bullet2.gif Sonofresco 2LB Profi...
bullet2.gif Artisan Devices
bullet2.gif Big Price Drop on Gr...
Hottest Threads
bullet2.gif Dereks 1-2Kg drum... [76]
bullet2.gif 2nd drum roaster [74]
bullet2.gif Rocquette Roaster... [34]
bullet2.gif Another electric ... [30]
bullet2.gif Stop roast before... [27]
Donate to HRO
Please enter your site username (if you have one) and your email address (required) to be sent with this donation for tracking and contact purposes.


Site Username
If you don't have a site username, just enter "Guest"


eMail Address **REQUIRED**

Users Online
bullet2.gif Guests Online: 5

bullet2.gif Members Online: 0

bullet2.gif Total Members: 4,908
bullet2.gif Newest Member: justinthomasleonard
BotSlap Panel
bullet2.gif Last check: 05/24/2017 06:17
bullet2.gif Slap count: 0
bullet2.gif Last checked ID: 5940
View Thread
Homeroasters.org » BUILDING A ROASTER » Drum Roasters
Who is here? 2 guest(s)
 Print Thread
Dereks 1-2Kg drum roaster build
dmccallum
Hello
Iím a recent joiner and starting to flesh out a design for a new 1-2Kg drum roaster. Iíve been impressed with a number of designs here and the level of innovation, particularly with the Arduino/Pi and gas control mechanisms. The potential to create a roaster comparable to commercial machines is interesting.

Iíve spent the last 10 years restoring lever espresso machines (thread of my current project here - http://www.home-b...rnazionale), I guess my attention was going to turn to building a roaster at some point.

Iíve gleaned as much as possible from this site, pinched a few ideas and attached some shots of my initial design. I liked the thread with the Probatino style design so Iíve borrowed that, and thereís a useful photo floating around of the drum internals from a San Franciscan SF-1 which Iíve also referenced.
Iím looking now for some steer as to whether the direction Iím going is correct.

Drum Size & Capacity
250mm x 250mm x 2.5mm mild steel with a volume of 0.0122m3 or 12.2L. Shaft will probably be 12mm.
I intend to be able to roast between 1-2Kg of green beans on basis that RoastableBeanMass = drum volume/10, so 1kg green bean = 5.8L give or take

Drum Design
Iíve noted comments to the effect that the likes of Probat prefer an equal diameter/length, so going with this. I've seen a range of opinion about drum thickness. I'm after something that will support roast-profiling so hence tending towards a thinner 2.5mm, but welcome comments.
The outer drum skin will be 1mm mild steel and will put ceramic-fiber blanket over this.
The rear of the inner drum will be a 1-2mm perforated mild steel with 3mm holes and a clearance of 30mm between it and the cabinet rear plate. About 28mm between the inner-drum and outer drum skin.

Cabinet
Will use 4mm mild steel for front and rear plates. The six stays will be 11mm steel hex section that Iíll tap at each end to take 8mm bolts.

Cheers
Derek
dmccallum attached the following images:
inter.jpg 2kg-concept3.jpg 2kg-concept2.jpg 2kg-concept1.jpg 2kg-concept5.jpg 2kg-concept4.jpg

Edited by dmccallum on 12/04/2015 05:32
 
Ringo
That looks good to me. It should work great. You will be roasting in no time.
All you need in life is ignorance and confidence, and then success is sure. Mark Twain
 
Tony_C
I can't wait to see it in action. Nice build!
 
allenb
Totally agree with the previous comments! Looks like you've put a lot of work into this design and everything I'm seeing looks like all systems go. On drum wall thickness, if you haven't already purchased the tube or sheet metal stock, my preference for that size drum would be closer to 1/8" but I'm sure the 2.5 mm will perform fine. Regardless of what size you go with I would include a baffle above the burner and prefer locating the burner off to one side instead of centering it which eats up less height to fit everything in. I'm sure you're already savvy to this but be sure and chuck the drum/shaft works into a lathe and true up the front face to allow keeping the drum face gap to a minimum.

BTW, I envy your ability to produce excellent graphics!

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
dmccallum
Thanks for that feedback. I'll get on with some of the finer design detail before getting materials cut.
 
hbboyd
Mine is just in the finishing stages and I went with very similar dimensions and design to yours. So far working great at your intended load sizes so I wouldn't have any hesitations!
 
dmccallum
I am investigating motors and think I have a solution for the drum, but thought to confirm what features in motor control I should be considering.

The drum motor has been spec'd to my drum dimensions and weight fully loaded at 7kg - an AC 15W std induction with a 1:20 ratio gearbox giving approx 70rpm with 1.7nm torque (http://www.ggm.co...on_15W.asp).

It has occurred to me though that I have seen people using various variac arrangements to control motor speeds (or was that for something else perhaps).
I'd have thought you would want the drum speed kept constant at about 70rpm?

Is there any desire/purpose to control drum or blower fan speeds?
Edited by dmccallum on 12/10/2015 10:18
 
hbboyd
Here http://www.ebay.c...0373333454 is the motor I used. It seems to deal with the load ok. It gets really warm but from everything I've read, you cant use motor surface temp to gauge if a motor is overheating. It doesn't seem to struggle though.

As for speed control, you'll see it on some roasters, I was always under the impression it is mostly just something you would adjust depending on load sizes. The goal being moving the coffee not so slow it sits and has tipping or goes too fast and gets pinned agains the drum (like that weird amusement park ride)...and has tipping. That being said, I do not have a variable, and I think I read somewhere the 50-60ish range works best.

Now for the fan, I used http://www.ebay.c...0573233180 with a Variac. Controlling fan speed I would say is super important, but that also has to do with the way I learned to roast (learned on a indirect fire roaster). Pretty much everyone I've seen does use it, but some use it more than others.

For subject of speed controlling fans, the best way to do it (with an AC fan) I know is a VFD, and I've seen those used on commercial roasters many times before. Many people don't want to spend that money, so do your research of what type you use and make sure your motor can take it, there are lots of cheap ways that will break it.

ADMIN: edited to make links live and easier to use.
Edited by JackH on 12/11/2015 04:51
 
Ringo
On controlling air through a fan the cheapest way is to put in a gate that restricts the air before it goes through the fan. Just like the choke on a carburetor. If you restrict the air before the fan the load on the motor will drop. You can not restrict the air after the fan because that will burn out the fan. On my drum roaster I have steel circle cut the size of the pipe coming out of the drum thats attached to a shaft. I can turn the shaft to restrict the air flow. I run boilers are work with 50 Hp motors running the draft fans and this is how they work. A pid controller opens and closes a big baffle to control how much air goes through. Now the fuel is controlled by a VFD because just like on a roaster you need fine control.

On my drum I overestimated how much air I need to roast so I normally run with my baffle only open maybe 10 percent. But nice to have the extra capacity because when i need to cool off the roaster I can run draft at 100 percent. I have marks on the side for air flow during drying, development and 1st crack. But for normal roasting I have my hand full adjusting the propane, still doing that by hand.
Edited by Ringo on 12/11/2015 05:16
All you need in life is ignorance and confidence, and then success is sure. Mark Twain
 
Ringo
This is not a roaster piece but this how it looks.
Ringo attached the following image:
tjernlund_abd_series_baffle.jpg

All you need in life is ignorance and confidence, and then success is sure. Mark Twain
 
dmccallum
Thanks for that Ringo, I imagine I'll go with this. I'm up-specing plenty aside and can always revisit at a later stage.

hbboyd, your motor looks much the same spec. I note you've gone with the 1:25 ratio gearbox. I may get the 1:20 & 1:25 when I order.
How'd you mount yours? Inline direct onto the shaft or ? I'm looking at a 90deg mitre gear arrangement.
 
hbboyd
Mine is mounted inline direct on the shaft, if I redo it, I would probably go chain drive. But for no reason other than i like it and it'll pull it away from an heat.
 
dmccallum
I'm starting to think about the cyclone and cooling tray arrangements. Want to keep things simple and ideally use only one blower for both air flows.

I've looked around and seen some machines with both drum and cooling tray draw pipes that appear to connect to the cyclone assembly. The attached pic of a SF-1 pipe arrangement is a good example.
Trouble is these are typically housed in enclosures and I've not seen a picture of one disassembled. I've an idea of what might be inside one but not sure as to what venting ideally should be going on (seen suggestions that drum venting should be continued after roast-end)

Can anyone advise?
dmccallum attached the following image:
sf-1_pipe_arrangement.jpg
 
Ringo
With chaff you are filtering out a big flake so you can keep you cyclone simple. You just need the inlet to come in at a tanget so the chaff spins this will make the it drop out. For home roasting you can just put a door in the bottom to open and clean out at the end of the roast. Put the suction fan on the top. If you fan is big you can put a T in before the cyclone to use it for bean cooling and roasting. If money is no problem I like to have a separate fan for the bean cooler. Look at the cyclone on the left for how they work. But you do not need the tapers at the bottom when you are removing chaff. Most coffee roasters I have seen use a straight tube with storage at the bottom. I would try to find a pipe that is not galvanized because of the fumes.
Ringo attached the following image:
cyclone_5.jpg

All you need in life is ignorance and confidence, and then success is sure. Mark Twain
 
dmccallum
Ahhh, well that's very useful! No need to get carried away with a complete Bill Pentze design then. Will simplify matters. Thx v much.
 
allenb
Another additional reduction in unnecessary complexity is to enter the cyclone cylinder straight-on instead of a tangent (as in the SF-1). Attach a 90 degree angled sheet metal baffle just inside the entry hole to direct the flow into a cyclone vortex. As Ringo mentioned, for separating light chaff flakes and other small particles from a coffee roaster, one doesn't need high efficiency. Plus, fabricating the parts for a tangent entry is a real pain.

Ringo, you mentioned using non-galvanized parts. All of the commercial cyclone systems and ducting I've worked on or came across in coffee roasting systems use galvanized and/or stainless. Most of them were passing straight roaster exhaust and not a mix which would have cooled down the air. I haven't seen any articles in the industry that suggest against using galvanized parts in this application. What I have seen is if one will be exposing galvanized parts to air/flue higher than 500 F and a food product is coming in contact with the air then there may be the possibility of contamination due to outgassing but I've never seen anything definitive written discussing those conditions.

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
Ringo
I never knew how hot was dangerous with galvanized, so i played it safe. Thanks for the info.
All you need in life is ignorance and confidence, and then success is sure. Mark Twain
 
dmccallum
hbboyd wrote:

Now for the fan, I used http://www.ebay.c...0573233180 with a Variac.


I've found the equivalent 230V version for this fan but have noted that both the 115/230 models are not recommended for speed control.
Can you expand a bit on how the motor performs and the variac mechanism you're using? Do you feel in hindsight it was the right one or could do with something more/less powerful?

Also, does anyone have any idea as what is the optimal spec of blower for a machine of this size (250x250 drum drawing through a 1 3/4" pipe) expressed in CFM? In otherwords what's the actual required max airflow?
 
MikeW
Hi Derek, maybe consider a permanent magnet DC motor. There are $11 PWM speed controllers that work really well.

I noticed there are AC gear motors available that are really inexpensive, but DC motors that do not have gearboxes are also very cheap (like $3 for than Johnson motor on surpluscenter).

I believe the important difference between AC induction, and DC permanent magnet, is that an AC motor will hold its speed under load but burn up if overloaded. A DC motor will slow down under load**, increasing its torque at the lower speed. I prefer the latter behavior but it is not always best for e.g. a drum motor.

**Unless you use an expensive constant speed controller.

For my drum I plan to use the $3 motor plus MXL pulley and PWM speed control. I don't think it will hold constant speed for all loads, b/c the motor is not that strong, but we'll see.

If you're wondering about different means to control air, talk to BoldJava (Dave Borton) who has tried both on several roasters. I've heard one person comment that having direct fan speed control is desirable, but it would be worth settling that question.

Drum speed can sometimes interact with coffee mixing, because beans may stay with the same vane each rev, depending on drum diameter and speed, and number of vanes. If your vanes perform different functions around the circle, that can be a problem. My drum is 6" and this may not be an issue for you.
 
BobbyM15
I have a geared DC motor that I am going to use but I am going to put an $11.00 PWM speed controller on it. If I load it with 3 lbs of beans I will just adjust the speed for that load.

In testing I have loaded the drum and ran that motor and speed controller for an hour at a time with no change in anything, so, I am happy.
Coffee is a language in itself.

Jackie Chan
x1
 
Jump to Forum:
Similar Threads
Thread Forum Replies Last Post
Sonofresco 2LB Profiling Roaster for sale JAVA TRADING COMPANY 1 05/23/2017 16:02
Cleaning my roaster HotTop Roaster 7 05/21/2017 08:52
Rocquette Roaster Build Building a Coffee Roaster 35 05/17/2017 04:23
Gas Fired Drum Roaster - Lets Build It Drum Roasters 25 05/15/2017 18:37
Syngas Heated Coffee Roaster Experiment Electric and Gas Heat Sources 3 05/13/2017 15:14
Member Poll
What region do you enjoy drinking coffee from the most?

Africa

Central America

Indonesia

Island Regions

South America

Columbian, my Columbian

You must login to vote.
Shoutbox
You must login to post a message.

JackH
05/24/2017 01:28
I think there always was a character limit on the shouts. Meant to be short messages.

jkoll42
05/23/2017 15:30
stupid character limit. continued.... [post as well as the shout]

jkoll42
05/23/2017 15:25
Thanks for getting the site back up. Only issue I've found is the quote button seems to just dump the whole thread. Well edit is working since I put ever instead of every and I could edit the pos

skpacman
05/22/2017 13:18
ThumbsUp

NetriX
05/22/2017 13:08
morning

JackH
05/22/2017 11:10
welcome2 Trevallion

JackH
05/22/2017 11:08
Welcome ronncat

JackH
05/22/2017 11:07
jamesvtt welcome cup

JackH
05/20/2017 14:43
welcome2 waxy

JackH
05/20/2017 14:41
Welcome hisokasbane

JackH
05/20/2017 14:36
Thanks Skpacman for getting us going!

skpacman
05/19/2017 16:37
I was trying to repair postfix to get email working again and the reinstall broke and took down the whole server.

allenb
05/19/2017 16:13
That's great news that you were able to get things recovered and back up and running. Any idea what caused your server to explode?

skpacman
05/19/2017 11:39
I apologise for the downtime. My server exploded...

allenb
05/16/2017 15:01
sapidus3225 Welcome