topbanner.gif
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Shoutbox
You must login to post a message.

snwcmpr
10/22/2019 5:31 AM
Thanks to you all....... I was not sleeping ... I stayed awake worried about it all. :)

Koffee Kosmo
10/21/2019 5:00 PM
While you were sleeping I have been active in booting out some spammers along with the posts they tried to sneak past me

NetriX
10/21/2019 2:41 PM
Apologies, fixed it asap! BBQ grill

snwcmpr
10/21/2019 12:35 PM
WOW!! A few minutes ago the site page said "Account Suspended". And would not open the site.

snwcmpr
10/18/2019 2:37 PM
Eth Nat Yirg Idido roasted yesterday. I dropped some off at a friends coffee shop. In a few days he will brew it and tell me what he thinks. We believe my roasts are better than what we buy.

Users Online
Guests Online: 3

Members Online: 0

Total Members: 6,205
Newest Member: komodo
In Memory Of Ginny
Donations

Latest Donations
renatoa - 2.00
allenb - 25.00
snwcmpr - 10.00
Groveland Hill Roas... - 25.00
renatoa - 2.00

View Thread

Who is here? 1 guest(s)
 Print Thread
Bobby M15's drum
BobbyS
The one on the front that is shown is a Spyraflo.

Edit: also on the back I have a contained 2 bolt bearing that I can lock the shaft with.
Edited by BobbyS on 12/24/2017 9:53 AM
 
BobbyS
Getting a little more done. Here is the trier I just finished.

The handle I ordered from these folks. Was inexpensive and I received it fast. I used the larger handle as I wanted as much distance from the hot end as possible lol.

http://www.lmii.c...ol-handles


i.imgur.com/9KA6TUpm.jpg

i.imgur.com/S0Kg6Ebl.jpg
Edited by BobbyS on 08/01/2018 6:54 PM
 
BobbyS
fixed
Edited by BobbyS on 08/01/2018 6:55 PM
 
renatoa
They are too perfect, imgur crashed when seen you parts :)
 
BobbyS
With Jacks great help! Thank you!

This is my trier I recently finished. Getting along on the rest of the roaster; trying to get the hopper finished up.

i.imgur.com/PO0oQ6ml.jpg




i.imgur.com/S0Kg6Ebl.jpg
Edited by BobbyS on 01/20/2018 6:12 PM
 
JackH
I edited your post and removed the ?1 that appeared after the jpg in your link. I do not see it in my Imgur links.


Download source  Code
[img]https://i.imgur.com/PO0oQ6ml.jpg?1[/img]



---Jack

KKTO Roaster.
 
BobbyS
JackH wrote:

I edited your post and removed the ?1 that appeared after the jpg in your link. I do not see it in my Imgur links.


Download source  Code
[img]https://i.imgur.com/PO0oQ6ml.jpg?1[/img]




Oh, ok, just takes someone who knows what they are doing lol.

Thank You!
 
BobbyS
Starting to make some headway finally. Got the cart started (with casters) which makes it so much easier to work on now that it is getting heavy.

i.imgur.com/0queItKl.jpg

Exhaust port.
i.imgur.com/FnM1Igdl.jpg

With the bean hopper door in load position it covers the exhaust port so no beans get away.
i.imgur.com/IOsU16Dl.jpg
Bean hopper door closed.
i.imgur.com/wZK4oGKl.jpg

i.imgur.com/hEDiuvGl.jpg
 
dmccallum
Looking good. I'm liking that hopper-gate assembly!
 
renatoa
Are these necessary to be SO massive... ?
Just puzzled... not critical.
I am asking myself this question every time I see a commercial roaster too, especially the small models, 1 kg seems close to 5 kg.
 
JackH
Nice work BobbyS!
---Jack

KKTO Roaster.
 
BobbyS
renatoa wrote:

Are these necessary to be SO massive... ?
Just puzzled... not critical.
I am asking myself this question every time I see a commercial roaster too, especially the small models, 1 kg seems close to 5 kg.


It is about 2kg, probably do a bit more and looks bigger than it is. It is about 14 inches across. Also it needs room for the heat chamber around the drum (not on yet) and insulation.

Yeah, go big or go home lol BBQ grill
Edited by BobbyS on 02/08/2018 10:08 AM
 
BobbyS
JackH wrote:

Nice work BobbyS!


Thanks Jack!
 
BobbyS
dmccallum wrote:

Looking good. I'm liking that hopper-gate assembly!


Thanks, I haven't tested it yet so we'll see how it works. Hopefully it will do well.
 
allenb
Very nice! Can't wait to see it tumbling some beans! BBQ grill
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
BobbyS
allenb wrote:

Very nice! Can't wait to see it tumbling some beans! BBQ grill


Lol, you and me both! Do you think 1" of space around the drum for the heat chamber will be enough? You can see where I marked it with a marker on the inside of the back plate.
 
allenb
1" should be fine. I went with 1/2" on my 1 lb drum trying to limit the total finished width but had some issues with the inner sheet metal layer warping and rubbing on the drum since I mistakenly left no room for the metal to expand in length (front to back). I should have left at least 1/32" gap.

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
BobbyS
allenb wrote:

1" should be fine. I went with 1/2" on my 1 lb drum trying to limit the total finished width but had some issues with the inner sheet metal layer warping and rubbing on the drum since I mistakenly left no room for the metal to expand in length (front to back). I should have left at least 1/32" gap.

Allen


How can it be attached if it moves with heat? I want to be able to keep insulation out of the heat chamber.
 
allenb
This is one of the more troublesome areas of a drum roaster design. The structural rods connecting the rear and front plates are necessarily rigid and do not expand/contract at the same rate as the inner liner since the two do not see the same temperatures. One option is to mount the shield using angle brackets with elongated holes and somewhat loosely attach with lock washers so the shield can move independently from the front and back plate assembly. You have to leave a little room between the plates and shield and insulation shouldn't fall through the crack.

Allen
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
BobbyS
well my roaster is going on hold after amputating about 1/2 inch off my right thumb tip with my 12 inch disc sander. bummed i am.
 
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
Drum Roaster Advice and Discussion Drum Roasters 8 10/14/2019 10:52 AM
My drum/bbq roaster Drum Roasters 5 10/14/2019 6:13 AM
New 1kg drum roaster build Drum Roasters 8 10/10/2019 9:53 AM
Another 1.5kg or 3lb drum roaster from scratch Building a Coffee Roaster 99 08/07/2019 5:48 AM
Drum material: which is the best Drum Roasters 24 05/26/2019 2:24 PM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion Copyright © 2019 PHP-Fusion Inc
Released as free software without warranties under GNU Affero GPL v3
Designed with by NetriX