topbanner.gif
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Shoutbox
You must login to post a message.

Oneal
Offline
· 08/05/2020 1:08 PM
Is anyone roasting on a Coffee Tech FZ 94? Using Artisan. Need help. thumbdown

mtbizzle
Offline
· 08/03/2020 11:26 AM
There is (or was? Grin ) a gesha at sweet marias...

snwcmpr
Offline
· 07/25/2020 12:31 PM
I ran out of Ethiopian Gesha.

snwcmpr
Offline
· 07/25/2020 12:31 PM
it is ok. I do not remember. I think it was a callout to the spam shout.

JackH
OfflineAdmin
· 07/24/2020 3:52 PM
Sorry Ken, I deleted your shout by mistake. Lots of shoutbox spam attacks lately.

Users Online
Guests Online: 4

Members Online: 0

Total Members: 6,675
Newest Member: Oneal
In Memory Of Ginny
Donations

Latest Donations
Anonymous - 5.00
Anonymous - 5.00
renatoa - 2.00
JitterzZ - 2.01
renatoa - 2.00

View Thread

Who is here? 1 guest(s)
 Print Thread
Setting up TC4 / Arduino / aArtisan
houstonroaster
Hello! I just wrapped up my first roaster build (modified popcorn popper). DC Motor and AC heating element, basically following the instructables article out there. Tested it with manual controls (on/off switch; wall dimmer switch for heater). All works fine, but I now want to connect to software. I have the TC4+ shield all set up and mounted to the arduino board, SSR ready to go (for heater control) and everything wired up.

But my arduino programming skills are level 1 out of 10. How do i get from hardware all wired properly to controlling with aArtisan / home roaster etc? Most instructions i can find just say pull files from github (https://github.com/greencardigan/TC4-shield/tree/master/applications/Artisan/aArtisan_PID/trunk/src/aArtisanQ_PID) and you're all set. But those instructions are written by software experts - which i am not - and there is something i'm clearly doing wrong! Does anyone have a little more step by step guidance here?

Thanks in advance!!
 
mg512
Where are you getting stuck? Or do you not even know where to start? Briefly:
1. Install the Arduino app.
2. Download the files.
3. Put all the libraries (among the files you just downloaded) into your Arduino library folder (location depends on your operating system - google for details).
4. Open the .ino file amongst the files you downloaded - the aArtisan / aArtisanQ_PID sketch will open in the Arduino app.
5. In the Arduino app, adjust any settings in user.h as needed.
6. In the Arduino app, select the correct Arduino type, serial port, and click upload.
 
https://www.tindie.com/products/15798/
houstonroaster
Thank you for the help! I downloaded all files from link above and put into “libraries” folder within arduino. When I open the “.ino” file, it just looks like jibberish. I’m no expert in Arduino but I know enough to see something looks off. Pic below, as well as picture of “user.h” screen. Any ideas? Thank you.
 
houstonroaster
I neglected to attach the pictures from previous post. Can't seem to figure out how to attach pictures....not coming through each time I do it. :) will have to try again later
Edited by houstonroaster on 07/10/2020 8:23 AM
 
mg512
Hm, hard to say without a picture, but if it's truly jibberish it could be a file encoding issue. I've never encountered that in Arduino, but I notice that under Tools there's a "Fix encoding & reload" option - maybe worth a try. Also how are you downloading the files? Probably best to download the whole repository (go to https://github.com/greencardigan/TC4-shield then click the green Download / "Code" button and select "Download ZIP") rather than try to download just the files in that folder individually.
 
https://www.tindie.com/products/15798/
JackH
RE: Posting Photos:

Use the Browse Button at the bottom. Select your file and it will show the filename below with a c:\fakepath location.
Keep your filename simple with no spaces or special characters.
You can click browse again for a second photo to add.
The system says you can add up to 8 photos, but that does not always work correctly.

It is important that you do not click "Preview reply" or "Preview post", it will clear the photos you selected.

forum.homeroasters.org/forum/attachments/capture_79.jpg
JackH attached the following image:
capture_79.jpg

---Jack

KKTO Roaster.
 
houstonroaster
Pictures attached for above posts! Thanks
 
houstonroaster
I am sorry everyone...can't seem to get photos to load. Seem to be doing everything right....shows uploading...no error messages but no pictures come through.
 
JackH
Are they .jpg?
---Jack

KKTO Roaster.
 
houstonroaster

Quote

mg512 wrote:

Hm, hard to say without a picture, but if it's truly jibberish it could be a file encoding issue. I've never encountered that in Arduino, but I notice that under Tools there's a "Fix encoding & reload" option - maybe worth a try. Also how are you downloading the files? Probably best to download the whole repository (go to https://github.com/greencardigan/TC4-shield then click the green Download / "Code" button and select "Download ZIP") rather than try to download just the files in that folder individually.


Thank you MG512! The Download ZIP option worked. Really appreciate the tip. No onto figuring out aArtisan.
 
mg512

Quote

houstonroaster wrote:
Thank you MG512! The Download ZIP option worked. Really appreciate the tip. No onto figuring out aArtisan.


Great, happy to hear!
 
https://www.tindie.com/products/15798/
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
Roasted/Bagged/Setting up time limits Roasting Coffee 1 07/31/2020 1:10 PM
TC4+ Arduino coffee roaster shield (TC4-compatible) Dataloggers/Controllers/Rate of Rise Meters 209 07/29/2020 7:05 AM
Heater Protection via Arduino Fluidbed Roaster 3 06/24/2020 4:49 PM
Arduino PID controlled popper Dataloggers/Controllers/Rate of Rise Meters 20 05/05/2020 3:48 PM
Has anyone made a case for the Arduino/TC4 (or TC4+) combo? Dataloggers/Controllers/Rate of Rise Meters 8 01/18/2020 7:14 PM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion copyright © 2002 - 2020 by Nick Jones.
Released as free software without warranties under GNU Affero GPL v3.
Designed with by NetriX