topbanner.gif
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Shoutbox
You must login to post a message.

JackH
OfflineAdmin
· 08/10/2020 8:46 PM
Had to make myself another cup of coffee to get through it.

snwcmpr
Offline
· 08/10/2020 7:33 PM
I went into withdrawal for a bit. Now .. all is good. roar

mtbizzle
Offline
· 08/10/2020 7:26 PM
Yeah Jack I think so, I couldn't access for a bit

JackH
OfflineAdmin
· 08/10/2020 6:51 PM
Did we lose the site for a while?

JackH
OfflineAdmin
· 08/06/2020 3:33 PM
Allenb, how are you doing?

Users Online
Guests Online: 4

Members Online: 0

Total Members: 6,687
Newest Member: merahbangsawan
In Memory Of Ginny
Donations

Latest Donations
Anonymous - 5.00
Anonymous - 5.00
renatoa - 2.00
JitterzZ - 2.01
renatoa - 2.00

View Thread

Who is here? 1 guest(s)
 Print Thread
inner bean dev, or total time?
mirza
im using custom sample roaster, drum capacity 200g. the only thing i can measure is time and batch size. i measure gas charge only with my eyes, seeing wether is big or small charge and adjust it with a regulator. i can't measure temperature.

question is, when i read about roasting they say to get an enough inner bean development, we need enough starting momentum, this require high drop temperature. but if we want to supress vitality for espresso blends, we need to lengthen total roast time, require lower drop temperature.
now, if i want to roast espresso blend, should i choose between high or low temperature? or can i get both inner bean development and reduced vitality in one method?

thanks for your attention.

nb: if you need more data to answer this, please reply
 
allenb
Unfortunately, typical sample roasters have historically been designed for very light cupping roasts to allow buyers a means to evaluate green coffee and have never needed precise controls nor bean temperature feedback. With that being the case, it will be difficult for anyone to give advice on best way to steer your roaster through a profile. My advice for coffee intended to be used as espresso would be to experiment with starting temperatures to find a temperature that allows arriving at a light yellow/tan color (end of drying) at 5-6 minutes and manipulate the the gas pressure to allow sliding into a browning phase that gets you to start of first crack by an additional 4 minutes. At first snips of first crack, back off on the gas to allow hitting your finish bean color in another 2 to 3 minutes.
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
mirza

Quote

allenb wrote:

Unfortunately, typical sample roasters have historically been designed for very light cupping roasts to allow buyers a means to evaluate green coffee and have never needed precise controls nor bean temperature feedback. With that being the case, it will be difficult for anyone to give advice on best way to steer your roaster through a profile. My advice for coffee intended to be used as espresso would be to experiment with starting temperatures to find a temperature that allows arriving at a light yellow/tan color (end of drying) at 5-6 minutes and manipulate the the gas pressure to allow sliding into a browning phase that gets you to start of first crack by an additional 4 minutes. At first snips of first crack, back off on the gas to allow hitting your finish bean color in another 2 to 3 minutes.


thank you very much, this answer is really helpfull. one more question if you dont mind. what is your advice for filter roast with sample roaster like mine?
 
renatoa
Finish is what establish the roast target, less than 2 minutes for filter, more than 3 minutes for espresso.
 
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
Bean blend for iced coffee BLENDING COFFFE 8 08/06/2020 2:27 AM
Roasted/Bagged/Setting up time limits Roasting Coffee 1 07/31/2020 1:10 PM
Total noob from Scotland New Members say hello or you may update your profile. 2 07/14/2020 3:14 PM
Green and Roasted Coffee Bean Sorter Equipment re-builds, reviews, fix it's and more 5 05/02/2020 4:18 PM
2" gate(knife) valves are expensive, bean dump Fluidbed Roaster 15 03/14/2020 5:39 PM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion copyright © 2002 - 2020 by Nick Jones.
Released as free software without warranties under GNU Affero GPL v3.
Designed with by NetriX