topbanner.gif
Login
Username

Password




Not a member yet?
Click here to register.

Forgotten your password?
Request a new one here.
Shoutbox
You must login to post a message.

Koffee Kosmo
OfflineAdmin
· 08/12/2020 5:37 PM
And I thought it was just me that couldn't access the site All good now - coffee kept me company

JackH
OfflineAdmin
· 08/10/2020 8:46 PM
Had to make myself another cup of coffee to get through it.

snwcmpr
Offline
· 08/10/2020 7:33 PM
I went into withdrawal for a bit. Now .. all is good. roar

mtbizzle
Offline
· 08/10/2020 7:26 PM
Yeah Jack I think so, I couldn't access for a bit

JackH
OfflineAdmin
· 08/10/2020 6:51 PM
Did we lose the site for a while?

Users Online
Guests Online: 1

Members Online: 0

Total Members: 6,688
Newest Member: AaronT
In Memory Of Ginny
Donations

Latest Donations
Anonymous - 5.00
Anonymous - 5.00
renatoa - 2.00
JitterzZ - 2.01
renatoa - 2.00

View Thread

Who is here? 1 guest(s)
 Print Thread
Roasting 101 Basics
allenb
Roasting Basics

The following 'basics' primer on coffee roasting was compiled from previous posts from Seedlings


Good article covering some of the basic progressions of a roast

Heating the green coffee should bring the beans to "First Crack" also known by "1C" or "FC" in 8 to 12 minutes. Sufficiently heating coffee beans changes the internal chemical composition in a similar manner as popcorn, and as the woody material (cellulose) of the bean heats up, the moisture will be released. This produces an audible "pop" similar to popcorn, but not as loud. Each bean will crack. Like popcorn this will start with a pop or two, then steadily progress to a "rolling crack" or a persistent popping, then taper off to a pop or two until first crack has finished. The conclusion of the first crack leaves a very light roast of coffee ready for grinding and brewing. This is commonly known as a "City" roast in roasting circles. Of course the coffee can be roasted darker if desired.

If a darker roast is sought after, keep roasting, watching, listening and smelling. At the onset of 1C the aroma turns from grainy, grassy, cereal smells and wispy smoke begins to develop. By the end of 1C, smoke will grow steadily stronger as will the aromas, until "Second Crack" begins. Yes, coffee cracks once, then cracks again as the roast progresses! The onset of 2C will bring continuous and darkening smoke, a sweeter, more intense aroma, and snap-crackling. 2C sounds less like the popcorn pop, and more like the crackle of snapping toothpicks or the sound of "Rice Crispies" cereal in milk. It is quieter than 1C. 2C will begin with a snap or two as 1C did and progress to a full crackling, then if roasting continues, fade out. This second crack marks the early stages of darker roasts. Oils in the coffee will be pulled to the surface of the bean. If the roast is stopped just prior to 2C, the roast is called "Full City" and can have a few oil droplets visible on the beans. Stopping the roast further into rolling second crack will yield a "Vienna" roast and the beans should be nearly covered with shiny oil. Stopping at the end of 2C is a French Roasted, very dark coffee. Once second crack has begun, the flavor characteristics that give the coffee bean its fruitiness or acidity, or delicate floral, or sweet chocolate will be caramelized and many of them lost. The resulting dark roast will be marked more by the degree it is roasted than by the distinctness the bean was given on the tree.

----------end article

0 to 300F (or yellow) is drying phase:
Try to get bean temp to 200 F as quick as reasonably possible then taper off the power from there to hit yellow somewhere between 4 and 5 minutes. Too fast brings 'grassiness' in most coffees and 'ashyness' in some low altitude beans such as Brazils, Kona etc. Too slow will flatten or mute the flavors.

300F to first crack:
Too fast brings higher percieved sharp acidity, slower brings nuttiness, too slow brings 'baked' flavor

First crack to finish:
Too fast tastes underdeveloped, flat. Too slow through this stage can also bring about a baked flavor.

From 300F on the beans should NEVER drop in temperature, always increasing.

The following basic profile is a good place to start for anyone not already familiar with roasting:

-4 to 5 minutes to yellow (300F)*

-4 to 5 more minutes to start of first crack (380-410F)*

-2 to 4 additional minutes to end of roast)**

*These temperatures are typical for the three major stages of roasting but depending on your sensor type and placement this can vary by several degrees +/-

**For light roasts where there may only be between 15 or 20 degrees from onset of first crack to finish, one should try and allow at a minimum 2+ minutes for proper development.
Edited by ginny on 08/08/2015 6:24 PM
1/2 lb and 1 lb drum, Siemens Sirocco fluidbed, presspot, chemex, cajun biggin brewer from the backwoods of Louisiana
 
Jump to Forum:

Similar Threads

Thread Forum Replies Last Post
Online roasting timer app ROASTING SOFTWARE APPS 1 08/13/2020 6:07 AM
Roasting station YOUR ROASTING/BREWING STATION 7 05/22/2020 8:36 PM
Cast Iron Wok roasting - triage Cast Iron Skillet Roasting 13 05/05/2020 11:25 PM
New to roasting (what to buy) WHAT SHOULD I BUY OR MAKE 11 04/26/2020 9:22 PM
Roasting for cold brew/iced Roasting Profiles 2 04/18/2020 12:58 PM
Homeroasters Association Logo, and all Content, Images, and Icons © 2005-2016 Homeroasters Association - Logos are the property of their respective owners.
Powered by PHP-Fusion copyright © 2002 - 2020 by Nick Jones.
Released as free software without warranties under GNU Affero GPL v3.
Designed with by NetriX